GENERAL. Usage of Maintenance Manual. FR-SF series inverters are designed to drive machine tool spindles, and feature quiet operation, stable and rapid. Hi all: Could anyone please explain the difference between the FREQROL FR- SE and FR-SF??? To me they sound the same I thank you for. Repair service for FR-SFK-CE Mitsubishi AC Spindle Drive 26kW VAC FREQROL FR-SF Condition: Send-in repair. Free evaluation. 6 Months warranty .
|Published (Last):||24 August 2011|
|PDF File Size:||13.30 Mb|
|ePub File Size:||15.21 Mb|
|Price:||Free* [*Free Regsitration Required]|
The up to speed signal o Check the external signal in o Take proper countermeasures or zero speed signal is the status display diagnosis by referencing Section 2 not issued. Check that the SF-OR or are determined. Sounds like your SF-CA is still alive. Between CH15 – CH9: NC through the bus is o Check that the set screws of not securely vreqrol.
Alternatively, the NF Appendix 5. Terms and conditions apply. Ol – 20 Parameter 5: Note To distinguish between a fault of the mechanical portion including the motor and that of the amplifier including the speed reference, take the following procedure.
The external speed o Increase the value of the o Correctly set the value fresrol reference is incorrect.
Note 1 Although the same parameters can be set from the spindle amplifier, when the bus line is linked, those being set from the NC become valid. Fanuc 18i i CNC Series. I plugged back in the Terminal strips one at a time and it’s only when the top one is in that the LED’s go out. Increase the parameter value. Get fast, free shipping with Amazon Prime.
This parameter value should be set in the manner that the ratio of 37 freqol 23 VKI -n loop the speed loop to the proportional 0 – integral type gain VKP becomes nearly constant. Philabuster liked this post. Item Cause Check Remedy The motion balance of o Rotate the motor at a high o Improve the motion balance the machine is bad.
We apologize in advance for this freqrlo inconvenience. Results 1 to 20 of Rotate the motor at the maximum speed and check that the amplitudes of the signal outputs for the forward rotation and reverse rotation are?
Be the first to review this item Product Warranty: OJS2check the signal wave- form. The number of gear teeth on the spindle However, on the NC 39 57 25 side against the gear 00 is converted screen, it is in the into hexadecimal notation and set.
Good Result guys, Thanks a lot, Mark. A guy in Malaysia of all places! An instantaneous power o In the same manner as the o See the alarm No. See offer for details. This item was removed from aWorking Machine, and is being sold in good condition unless otherwise stated!
At the time, the switch PBl only once address display LED steadily after all data write operation is com- lights rather than blinking. In case of analog card.
The insulation resist- o Remove the wires of the o Check the portions whose ante of the amplifier is phases R, S, and T of the insulation is degraded and degraded.
Ground a cable which connects the motor ground and controller ground. Note The stop position is controlled by a bit contact ffr OlH to 12H and is controlled by the follow- ing equation.
The override command is o Check the override command D Turn off the override com- input. Do not press this switch while the motor rotates.
The motor cooling systen st Visually or by touching the D Clean the cooling system is dirty. Item Cause Check Remedy The dr relating 0 Compare the following para- o Correctly set the parameter to the synchronous meters which are set on the values.
A bad transistor will have one or more totally different readings. Freqro “1” is set to Y45wT bit 8, this parameter is valid. See questions and answers. These parameters are sent from the NC when the spindle amplifier is linked with the bus line.
At the time, when is not linked dle the bus line has not been through the bus: Remove the P flat head screw which fastens the fan motor main body and the fan motor frewrol unit can be dis- mounted from the fan case.
Note If the alarm No. Original value on T32 QT’s I have seen is about Indexing input Standard setting: It should be the same as the ff, axis Z ting: Next, thoroughly check the contents of Table 1.