ORG. GND. 8-lead SOIC. 8-lead dBGA2. 8-lead PDIP. 8-lead SOIC. Rotated (R). ( 1K JEDEC Only). 8-lead mini-MAP (MLP 2×3). 8-lead TSSOP. DO. DI. NC. VCC. CS. SK. 1. 2. 3. 4. 8. 7. 6. 5. GND. Normal. Pinout. Rotated. Pinout .. 93C Address bits pattern -> User defined. Timing Diagrams. Address. 8-lead SOIC. 8-lead dBGA2. 8-lead PDIP. 8-lead SOIC. Rotated (R). (1K JEDEC Only). 8-lead Ultra Thin mini-MAP (MLP 2×3). 8-lead TSSOP.
|Published (Last):||4 October 2014|
|PDF File Size:||16.85 Mb|
|ePub File Size:||6.33 Mb|
|Price:||Free* [*Free Regsitration Required]|
Blank A B C. Pomona Electronics – http: Therefore we can return your samples rotatee if we get chips from semiconductor manufacturer. It was rotated, refitted it and radio now says error 3, so I think I have buggered it one way or the other, Still works if you hold down the band button and turn it on but it beeps all the time.
The real chips are also necessary to have in the case of reproducing issues from the created support. MEMprogL discontinued Direct connection.
IT yes, they are: Device search Fulltext search Supported devices. Maybe it is rotated, did you check on what pin is gnd? Reasonable quantity of this product can be available within 3 working days.
The names of the chips rotats our database contain all characters necessary for identification of the device, but don’t contain such codes, that have no influence to the programming, for example temperature codespeed codepacking type codeetc. Before years i tryed to read one rotated chip as normal, more than times and ofcourse i did’n read it, then i ask a friend and he say that maybe it is rotated and i tryed it like rotated and read it sucsessfull, so there was not problem.
Thanks MH, I think I will have to do that, sorry about your programmer, if it’s the one I think it is, there is only a handful of components on the board, cant you find out what’s faulty, or are you getting them replaced under warranty?
Device Search tip The rotste of the programmable devices in our database don’t contain all charactersshown at the top of the chip or mentioned in a datasheet section part numbering.
Thanks for the info on the 93c MEMprog discontinued Direct connection. Yes I have had CDH gear for about 15 yearsthe first interface i had had a sine wave generator for doing the early Philips radio’s with ER Move the cursor over the box to highlight particular section. MEMprog2 discontinued Direct connection. Any help would be appreciated. Read with a LV48 programmer. BeeHive8S discontinued Direct connection.
This number indicates quantity of items that could be produced from components in stock. If such code letter is at the end of the name, it should 93c4 omitted.
Would I have damaged it if it was not rotated, and I read it as rotated. My CDH Electronics gear has thrown it’s teddy out of the pram again, and has to go back to see Colin, so I’m trying to read it with an Asix Presto, I wired it up as a rotated 93c46 and was unable to read, so tried as a normal one still the same.
If gnd on radio is on pin5 on pcb, so chip is normal, if gnd is on pin7 on pcb, so chip is rotated. In case of missed samples, we always asking the semiconductor manufacturer for samples, but if samples are not available – also in the package you’re asking for the support – the solution from us will be delayed.
PIKprog2 discontinued Direct connection. Last time I tried it would not re-install, and so 9c46 am sending it back for later software to be added. The sample of programmable devices is necessary to have for test and release new chip support.